GD 010 05 KM SucomA GP Communication Driver

The protocol driver for the Digital GP - x3x and GP - x7x Series Graphic Panels to connect with a Klockner Moeller SUCOS PS 306 or PS 316 Programmable Controller. The Driver uses serial communication with the controller through the RS-485 port.

There are two different addressing schemes available for accessing of PLC memory areas: symbolic or absolute address. The following PLC memory areas are supported: Flags (Markers), Binary Inputs and Outputs, Analog Inputs and Outputs, Absolute Address Bits and Words, Processor Status Word, Diagnostic Word, Information Word.

The driver file name for GP - x30 series is KMSUCOMA.ppg (V1.02). The driver file name for GP - x3J series is KMSUCOMA.ppj (V1.02). The driver file name for GP - x70 series is KMSUCOMA.apn (V1.01).

GD 010 10 KM PS4 GP Communication Driver

The protocol driver for the Digital GP - x3x , GP - x5x, GP - x7x and GP - x77R/GP - 2x00 Series Graphic Panels to connect with Klockner Moeller PS4 - 201 PLC. The Driver uses serial communication with the controller through the RS-232 port.

Due to the dynamic memory management in the Klockner Moeller SUCOcontrol PS4 PLCs, the KM PS4 GP Communication Driver supports access only to markers of the basic unit. Other operand types (inputs, outputs, parallel bus markers, etc.) can be accessed through the basic unit markers by adding appropriate instructions in the PLC program. The start and end addresses of the active marker area are determined at Communication Driver startup.

The driver file name for GP - x30 series is KMPS4.ppg (V1.01). The driver file name for GP - x3J series is KMPS4.ppj (V1.01). The driver file name for GP - x5x series is KMPS4.ppn (V1.01). The driver file name for GP - x70 series is KMPS4.apn (V1.02). The driver file name for GP - x77R/GP - 2x00 series is KMPS4.epn (V1.01).

GD 030 05 LON GP Communication Driver

The network driver for connecting the Digital's Graphic Panel (GP - x3x and GP - x7x Series) as a host processor to a Serial LonTalk Adapter (SLTA) in a LONWorks network. The RS-232 serial interface is used for data exchange between the GP and SLTA. The Communication Driver is primarily intended for use with LONWorks nodes included in the LONWorks network.

The addressing system used in the LON GP Communication Driver allows access to the LONWorks network variables as polled or unsolicited data. The update commands for a group of nodes are supported. The index addressing is used for polled data. The selector addressing is used for unsolicited data and for group commands.

The driver file name for GP - x30 series is LONGP.ppg (V1.01). The driver file name for GP - x3J series is LONGP.ppj (V1.01). The driver file name for GP - x70 series is LONGP.apn (V2.03).

050 05 Russian language package for GP - x5x and GP - x7x Series

Russian language package for GP Panels allows create an application with Cyrillic fonts. The Cyrillic fonts, Cyrillic keyboard driver and complete keyboard are included.

Includes demo screen and installation instructions.

GD 050 06 Greek language package for GP - x7x Series

Greek language package for GP Panels allows create an application with Greek fonts. The Greek fonts and Greek keyboard driver are included.

Includes demo screen and installation instructions.

GD 060 06 SCHIELE GP Communication Driver for GP - x70 Series, GP - x77R and GP - x77L/S Series

The SCHIELE systron GP Communication Driver allows the automatic communication between the GPx77R and GPx77L/S Series Graphic Control Panels (GPs) and SCHIELE systron S200/S250/S250c Programmable Controllers (PLCs). The Communication Driver is tested on GP-37W2/477R/377R connected to SCHIELE systron S200/S250 PLCs.

The Communication Driver on the GP uses the Schiele Programming interface Communication Protocol as well as the Schiele Data Access Protocol to read and write particular data fields inside the Schiele PLC.

The driver file name for GP - x70 series is SCHIELE.apn (V1.00). The driver file name for GP - x77R series is SCHIELE.epn (V1.02). The driver file name for GP - x77L/S series is SCHIELE.hpn (V1.02).

GD 070 05 Omron Ethernet GP Communication Driver for GP - x70 and GP - x77R Series

Protocol driver for the Digital GP graphic panels to connect Omron Ethernet PLCs. Driver supports also unsolicited messages. Following PLC's series are supported: C, CV and CS1.

The Driver supports four types of communication:
1. Driver acts as a master node polling Omron PLC. This is point-to-point communication, only one PLC of those on the network can be accessed at same time.
2. Driver treats unsolicited write messages from PLC program. This is multi-point communication, the messages can be received from every PLC on the network at same time.
3. Driver supports a subset of Memory Link Communication.
4. Driver receives and sends the user screen files from and to PC on local as well as on global network.

The driver file name for GP - x70 series is MTOMETH.apn (V3.20). The driver file name for GP - x77R series is OMRONETH.epn (V1.02).

GD 080 05 Movitrac GP Communication Driver for GP - x70 and GP - x77R Series

The MOVITRAC 31.. Frequency Inverter GP Communication Driver allows the automatic communication between the GPx70/GPx77R Series Graphic Control Panels and MOVITRAC 31.. Frequency Inverters (MOVITRAC 31..). The Communication Driver is tested on GP-470/270 and GP-477R/377R connected to MOVITRAC 31C015-503-4-00.

There are two groups of GP devices (data areas) supported: 1) devices that access a single parameter on MOVITRAC 31.. by its name and 2) devices that access voluntary parameters by their indexes (multiple parameter devices).

The driver file name for GP - x70 series is MOVITRAC.apn (V1.01). The driver file name for GP - x77R series is MOVITRAC.epn (V1.01).

GD 080 06 SEW Movidrive GP Communication Driver for GP - x70 and GP - x77R Series

The MOVIDRIVE Drive Inverter GP Communication Driver allows the automatic communication between the GPx70/GPx77R Series Graphic Control Panels and MOVIDRIVE Drive Inverters. The Communication Driver is tested on GP-470/270 and GP-477R/377R connected to MOVIDRIVE MDV60A0015-5A3-4-00.

The driver file name for GP - x70 series is MOVIDRIV.apn (V1.01). The driver file name for GP - x77R series is MOVIDRIV.epn (V1.02).

GD 080 08 DANFOSS Frequency Inverter Communication Driver for GP - x77R/GP - 2x00 Series

The DANFOSS Frequency Inverter GP Communication Driver allows the automatic communication between the GPx77R/GP2x00 Series Graphic Control Panels and DANFOSS Frequency Inverters.

The driver file name is DANFOSS.epn (V1.04).

GD 090 05 Unitronics M90 GP Communication Driver for GP - x77R Series and GP - x77L/S Series

The Unitronics M90 GP Communication driver allows the automatic communication between the GPx77R Series Graphic Control Panels and Unitronics M90 OPLCs (Operator panel & PLC) over the RS-232 link.

The Driver accesses the directly connected OPLC as well as the further OPLCs on the CAN bus. The server supports the Two-Way facility for DIGITAL's Pro-Server.

The driver file name for GP - x77R series is OPLC_M90.epn (V1.02). The driver file name for GP - x77L/S series is OPLC_M90.hpn (V1.02).

GD 100 05 GSM/SMS GP Communication Driver for GP - x70 Series

Protocol driver for the Digital GP graphic panels to connect GSM modem (Siemens M20 Terminal) to Digital's GP - x70 panels. The driver supports sending/receiving GSM Short Messages to/from GP. Also the voice calls from GP and receiving incoming voice calls to GP are supported.

The driver file name is GSMSMS.apn (V1.06).